İstaBreeze Kanat Flanşı Beş Kollu - 90 ve 107 cm Rotor Kanatları için
indirim
Havale ile ödemerlerde
%2 indirim
Şu an sitemizde 7
ziyaretçi ürünlerimizi incelemektedir.
- Diameter: 390mm
- Blade assembly M8
- Hole diameter (handle): 19.5 mm
- Steel, 5mm thick
CHARGING CONTROLLER CONNECTION ISSUES TO BE CONSIDERED!!!
one. Install the charger close to the battery and in a place that is not hot.
2. Install the load resistor horizontally away from the battery and controller.
3. First, connect the + ends of the battery and the charger, then the – ends, then connect the load resistor (resistor) to the load outputs and the 3 phase (ph) inputs from the last turbine.
4. Check that the terminal connection screws are well tightened.
5. Check that the charge controller inverter and battery pack are at the same volt.
6. In order to stop the turbine manually, you can use a switch (63 k automaton or 3x25 on-off pako) between the wind turbine and the charge controller, which will reduce the three-phase short circuit if necessary.
7. Be sure to ground the body of the pole.
8. The length of the pole can be around 6-12 meters.
9. You can mount the pole tightly with ropes from 3 sides against wind jerks.
10. While the charger is connected to the system, do not drill anywhere on the device with a drill. If you are going to drill for assembly, the device must be in the off position.
Teknovation Arge Bilişim Dan. Ltd. Sti. It was established by the Young Entrepreneur Electrical-Electronics Engineer Hamdin Bağçeci as a state-supported R&D company and continues its commercial activities in the field of Solar Electricity Generating Systems, increasing day by day with customer satisfaction.
In solar systems, we try to help our customers as much as possible with the right product and the right price.
A little warning to our customers. They should be careful about the unbranded, unlabeled Solar Panels removed from the power plants and the batteries that are trying to be sold as gel but are not real gel. We would like to share the information that such products are not allowed in our company. Of course, it is important to consider these when making price comparisons.
Wing Flange Five Arms
- Diameter: 390mm
- Blade assembly M8
- Hole diameter (handle): 19.5 mm
- Steel, 5mm thick
CHARGING CONTROLLER CONNECTION ISSUES TO BE CONSIDERED!!!
one. Install the charger close to the battery and in a place that is not hot.
2. Install the load resistor horizontally away from the battery and controller.
3. First, connect the + ends of the battery and the charger, then the – ends, then connect the load resistor (resistor) to the load outputs and the 3 phase (ph) inputs from the last turbine.
4. Check that the terminal connection screws are well tightened.
5. Check that the charge controller inverter and battery pack are at the same volt.
6. In order to stop the turbine manually, you can use a switch (63 k automaton or 3x25 on-off pako) between the wind turbine and the charge controller, which will reduce the three-phase short circuit if necessary.
7. Be sure to ground the body of the pole.
8. The length of the pole can be around 6-12 meters.
9. You can mount the pole tightly with ropes from 3 sides against wind jerks.
10. While the charger is connected to the system, do not drill anywhere on the device with a drill. If you are going to drill for assembly, the device must be in the off position.
Teknovation Arge Bilişim Dan. Ltd. Sti. It was established by the Young Entrepreneur Electrical-Electronics Engineer Hamdin Bağçeci as a state-supported R&D company and continues its commercial activities in the field of Solar Electricity Generating Systems, increasing day by day with customer satisfaction.
In solar systems, we try to help our customers as much as possible with the right product and the right price.
A little warning to our customers. They should be careful about the unbranded, unlabeled Solar Panels removed from the power plants and the batteries that are trying to be sold as gel but are not real gel. We would like to share the information that such products are not allowed in our company. Of course, it is important to consider these when making price comparisons.
